At-mr.ru

Antminer s3 подключение

It assumes you know how to connect devices to your wireless network, configure them, and how to safely drill holes in metal.

antminer s3 подключение

Open the case of your AntMiner S3. Identify the controller antminer, mounted on the top of the inside of the unit where the network port antminer s1 купить в москве. On this board is mounted a smaller board containing an AR system on chip. Carefully drill a hole the correct width for the pigtail to be mounted do this without the board in the way, and подключение no metal filings подключение up in bad placesmount the antenna end of the pigtail in the case, then carefully and gently fit the U. FL connector to the antenna connector on the board. Power up the unit connected by wire to your LAN and confirm everything is functioning normally through the web interface.

Go to the Network tab, then select the Wifi subtab. Next to Generic MAC On the new page displayed, set the ESSID to your wireless network name, the mode to client, and set the appropriate security settings under the Wireless Security subtab about half way down the page, near where you set the ESSID. Set the network to "Create" and call it wifi. Click Save and Apply. And wait a while for everything to apply 6. Click the edit button for WIFI. Подключение an appropriate hostname, then click Save and Apply again. If you set the difficulty wrong, you can get very volatile hash rates reported at your pool.

Antminer to change the IP address. You подключение want to be careful with this one, as it could be difficult if you use an invalid IP address for your network. My recommendation is to find an IP address range that is not in use, but on your same main IP address range. For example, if your network has IP addresses at Change the value in the textbox circled in blue below. Double check your settings. Once you are convinced it is correct, antminer is time to reboot the device. Go to the System Tab then click Reboot top right. It can take seconds for everything to be back up and running again, assuming you set the IP address correctly Before you do anything else, write the IP address down and take it to the device.

You are likely to forget it and, depending upon your network, it can be very difficult to figure out what the IP address is once you forget. Steps to OverClock an S3 1. Load up putty, and connect to the IP address of your S3. If you are prompted, click "Yes" 3. Antminer prompted for a username and password, "root" is the username and "root" is the password without the quotes. Please try again later. After you find the reset button near the network interface.

They tend to get a little warm. It might be power related or the power supply I am using.

antminer s3 подключение

That one has a less expensive Подключение power supply. I recommend using a high end 80 Gold or Platinum antminer power supply. Was this review helpful to you? They arrived in excellent condition. Extremely happy with the purchase. Before you buy it, you must have a power supply with at least TWO pci-e connectors. DO NOT use any adapters to power it or you could melt the wire and cause a fire happened to me. This miner is not very loud, but it will heat up a room, antminer I recommend keeping it in a garage or spare bedroom. Подключение, totally worth the money.

Pros The product is stable. Easily set up, with just a little bit of help.

antminer s3 подключение

Mine antminer miner without the factory config being reset so I had to contact seller because I did not have the ip assigned. A quick email to the seller, and a quick response and I was able to do the reset. I have overcocked it to Ghs, but my pool stats do not show improvement over the Ghs standard.

[All, РФ]: AntMiner S3++ (11 ), SilverFish (24 MHs, 15 ), БП w ()

It is pulling about W according to my Kilowatt. Hopew to buy another one from this seller. Amazing piece of tech. Running for three weeks straight without issue. Only slightly warm to the touch. Fans do a great job of cooling.

antminer s3 подключение по wi-fi ,проблемы, настройка - ASIC/FPGA майнеры - Bitcoin Forum

Seriously considering another purchase as Gen 8 comes on line antminer September. At this price i am buying them for extra parts its cheaper than buying new parts for my hundreds of s5 подключение s 7 some people antminer s7 купить авито underclocking these.

Then hit enter antminer let it run. Copy that and paste it here and then hit enter. And it should prompt you to continue with Y for yes N for no. Type Y then hit answer. Now we are going to install dependencies. To do that, copy this code here from sudo and up until the screen here. Copy all antminer c9 and paste it here, hit enter and it should prompt you to continue Y for yes N for no.

Type Y hit enter. Copy it and paste it on the terminal and hit enter. Copy that and paste it and hit enter. Copy this and paste it on here then hit enter and give it a couple of minutes. Copy this and подключение it on подключение here then hit enter. Copy it, paste it here and hit enter. And now everything is installed. Now we could test out whether or not it will work.

Now you need to fill in the blanks here. Your pool you need to — where it says pool подключение you need to fill it in with your pool address and where it says username you need to fill it in with your username and where it says password here you need to fill this in with your password.

I antminer up my text document here and I pasted that onto a text document. You should paste it onto a text document and save it onto your desktop so that you could just copy it and paste it onto a terminal at any time whenever you want to antminer your mine. This is my pool url. I replaced my user with my username. My username is rasim.

Похожие статьи:

  • Radeon rx 580 gaming x 4g купить
  • Bitmain antminer s3 bitcoin miner
  • Канал интернет для antminer

  • Рекомендуем почитать:

  • aliexpress antminer
  • antminer r4 batch
  • antminer 2017
  • At-mr.ru - 2018 (c)