Test the 3 hash boards one by one to controller and let it running antminer about 5 minutes, find out the issued hash board and ship it back to repair. If that hash board works well, you can keep it. There is no need to repair it until the hash board is totally defective. The hash rate is lower than normal. It may be caused by the instability of the power supply voltage or the defective hash board. First of all, please replace the power and 18 pin cable to try.
Some chips are lost. X shown on the Hardware Version. Hash board cannot be detected. There is no information shown on the Miner status interface. The miner works with normal hash rate when it was booted firstly. After a while, there is no hash rate. A large number of antpools increased unreasonably.
Hash rate is antminer. There is no или resetting the router. There is a short circuit inside one of the hash board. It leads to automatic protection. The miner will get burnt powered by или PSU of poor quality. Test the miner with multimeter to find which part is defective. Remove the defective part to repair. The PSU is defective. The hash boards are extensively defective resulting from the frequent network disconnection and continuous power supply. The miner tried to connect network frequently, which lead to program error in hash board. Catkins are как устроен antminer s9 to cause internal miner cold road congestion.
The control board cannot get power as the power section circuit in IO board is damaged. Hi, mi new S9 it doesnt works with the 3 has board, i can see one of them in the miner status. What can i do? Also switched a good hashboard to the bad miner, and was working Ok. Should I send it to repair? If you have not already done so please email us at support bitmain. We can help you with your specific issue.
I get the hardware version x. Curious thing, I own 02 Antminers S7, and both came up with the same issue at the same time. Thank you for submitting a ticket.
I have responded to the ticket with the information that you requested. Hi, i have an S9, and one of the boards showme a lots of "x", then i restart my miner, from the control panel, now the board doesnt turn on. I need to remove the damaged board to send it bitmain. I have my s7 cards have been damaging, sometimes when the frequency of to step back on sometimes not and in one of the cases the card comes on but the s7 does not have the или power или not reach 4. All 17 of my miners stopped working at the same time and now say "socket connection failed, Good morning, I request your help since my S9 has presented a problem. The temperature of the third hashboard is no longer displayed and two groups of zeros have disappeared in the ASIC state.
This has caused the hash rate to be less than normal, obviously the hashboard does not work antminer купить в москве. Reset antminer S9 and the values will not be reactivated. What can I do to resolve this situation? Air in fan spins at startup the exhaustr fans spins toward the end of the boot antminer at high speed only.
Hi, please submit a support ticket so that we can help you troubleshoot. You can submit the ticket right from our web site.
I have a problem. Chain 6 is not shown in the tabs "Miner status". Chain 7 does not show the temperature of chip 1 and chip 2. I turn on the s9, the red led light on the chain 6. What should I order for repair? I still have a guarantee. Same issue for me 6. One of my hashing boards does not show up or work anymore. I put so much into this. What do I do antminer Has this problem been или for anyone? Hi Edward, please submit a support ticket so that we can help you troubleshoot. Please include screen prints of the miner status and the miner overview, and a picture of the SN tag that shows the hash rate. Yes I have submitted support tickets and I just added screenshots in the reply section of the support e mail.
Can you confirm you have received it? They will not send you a new card bitman antminer l3I was told to ship the device entirely to China.
You are lucky, there is a service center in the USA, but in Russia there is not. I asked to send me a fee, I will или it myself. This is antminer news. It seems like if the other two boards are working fine then sending a replacement board would be the best option. I am still under warranty but I really do not want to send the whole machine back and pay shipping in addition to losing the mining profits and risk more damage or the miner getting lost in the mail.
I talked bitmain up a lot and referred a lot of friends and now I am really worried. I was told by support when I ordered that these machines should last for years. So bummed out right now. Wishing I never decided to mine right now guess everyone antminer s7 купить в украине right.
Hi Edward, I just sent you instructions to first try resetting the miner. All members of the BitcoinMining subreddit are expected to read and follow the Official Reddit Rules as well as the informal Reddiquette guidelines. Likewise, all moderators of this antminer do follow the Modiquette. Comparison of all mining pools on the official Bitcoin wiki. I run small, outdated miners at a loss pointed at a P2Pool node because I like to или so. Thinking of picking one up soon. Which would be the better option overall? Leaning towards the l3. L3 at the present but it is unlikely the profit margins are sustainable, should expect significant correction in coming months.
If you believe antminer LTC, antminer by all means please contribute to the network by mining it. I plan to mine LTC eventually, just not now because I expect a correction due to the ridiculously profitable mining right now - или difficulty will shoot up or price will come down to match the cost of mining. I came across mining rigs while searching out hardware to build a private deep learning rig. While it may not be as capable as this dedicated hardware, it gives you the option to switch to alternative currencies if one becomes less profitable, and at least leaves antminer s7 wikipedia или hardware you can use for other purposes or resell if things go south.