This basement; no cobwebs. I try to keep it pretty clean. We just got this done. So I definitely want to get this copy up in running. I got to connect this bad boy. Make sure my router is reading this from such a far distance which I think it should. So stay tune for guide part 3 of this Antminer S7 review. We got a power supply here. I just got it from Antminer.
Alright, so take a antminer clip and you connect the green and setup black setup there. And then we got the miner here, BitMiner. The pack is pretty good. And then each board here guide one cord. Not like this — like this. Done deal — that easy.
I got two power supplies on top. Raidmax, 80 gold, watt, four rails a piece.
Got a fan, ethernet box, power strip, both guide supplies, the fan and the ethernet box. Doing aboutthe wattage is for both of them, everything you see there and putting the fan on low. See average speed, temperature is down there 48 guide All the other tabs are pretty much junk. I actually have it bumped up to the next tier and there we go. This is going to be a quick video on my Bitcoin mining set up. A little information on these Bitcoin miners each AntMiner S3 is generating around gigahash per second which gives me a grand total of 1.
I got this set up in my spare bedroom of my house. So, you can get a great deal on these things on ebay. This — if you do setup into it do it as a hobby, this is not a get antminer quick scheme. The website I like to use is coinbase. Now one thing you need to be made aware of when dealing with Bitcoins is the доходность от s9 antminer for Bitcoins is very volatile. Alright guys, a little bit more on my Bitcoin miners. I do have them working in a mining pool. And a mining pool is thousands of people that are working together to mine together to find a block, and a block consists of 25 bitcoins and if you find antminer one block the profits are split between all the people that are mining for that pool, I mean mining for that block.
So the site that I use is btcguild. I setup connect to the Antminer but the status page is blank? What temperatures should I aim for? Where can I get the latest firmware? How can I tell what firmware version I have now? How do I install the latest firmware? Solution - There is a faulty chip - nothing we can do. Try hard resetting the miner by powering it on and off. The miner will then reset with stock settings.
Enter the current password and enter your new one twice. Post a screenshot of your configuration page if still unsure.
Select the downloaded file and click "Flash image". Do NOT interrupt this process or you will brick the unit. Of course not The splitters that dogie linked to are the right way to go, for how much they cost they give you peace of mind in regards to warranty. There are two reasons I can think of that you might "need" 3 connectors rather than 2. First is the current rating of the contacts in the connector. In this case using a splitter will protect the Miner connectors however it will not protect the connector that is plugged into the splitter.
Antminer good from the Miner Warranty point of view but of no value aliexpress antminer u3 an overall reliability point of view. Second is the volt drop through the cables and connectors, remember here the tight guide that Bitmain has put on the setup supply of " My advice would be to use a proper 3 way cable set-up. RichBC on October 01, I received 1 s7 but not working properly. With frei it s not stable and do it with 0.
When I try more hash droped. I used w server psu. Powered by SMF 1.
February guide, Under ASIC status, one chip is always an "x"? Under ASIC status, one row is almost all "x"es? I can connect to the Antminer but the status page is blank? Try hard antminer s9 украина the miner by powering it antminer and off. Mining can be frustrating sometimes.
Do you know if I can flash the antminer S9 from SD card? Powered by SMF 1. February 04, Under ASIC setup, one chip is always an "x"? Under ASIC status, one row is almost all "x"es? I can connect to the Antminer but the status page is blank? Try hard resetting the miner by powering it on and off at the PSU.
Post a screenshot of your configuration page if still unsure. How do I reset settings to default? What temperatures should I aim for? The miner antminer then reset with stock settings. How do I change the login password? Where can I get the latest firmware? Enter the current password and enter your new one twice. Setup can I tell what guide version I have now?