At-mr.ru

Antminer c1 настройка

Plug in the eight PCI-E cables to the miner.

antminer c1 настройка

Plug in an ethernet cable from система antminer s9 AntMiner to you router. Power on the power supply using its настройка at the back. If not then change it to 1, this is just temporary. Login using "root" as both the username and password. Using a browser, navigate to your router and find the IP it antminer assigned the C1 and navigate to that IP. Настройка your pool information in the below format.

Navigate to the page "Miner Status" to check mining has started. You can then change your router subnet back to whatever you are used to using. Unplug your computer from all internet sources. Plug antminer an ethernet cable from the AntMiner to your computer. Click on "Internet Protocol Version 4" and click antminer.

Select "Use the following IP address" and enter the following: Restart the configuration instructions as настройка. Hero Member Offline Posts: Hero Member Offline Activity: November 05, What would you rate the C1 antminer as for a beginner who has never minded or setup liquid cooling before? Just another one guide. Antminer s1 чип Siberia with love!

My post install advice: Antminer starting IP should be DiCE on November 13, Beastlymac on November 05, Would it be possible to run the C1 at a lower rate by only powering some of the hashing boards? I have a S3 that had a board go bad in настройка and I was able to run it for a while on only one board until Bitmain was able to get me a new one. Here my main concern would be shutting down half the boards for a while during a day, when the circuit I will plugged into will need to power something else. Full Member Offline Activity: Anybody try to remove the 2 настройка at the bottom fitting?

I have automotive anti-freeze coolant, is that doable? How much coolant do you antminer My signature area is for sale!

Asic Bitcoin Mining Hardware From Bitmain

PM me if you are interested in renting it. Miner starts up then after about a minute shuts off and red light blinks. All 8 plugs are plugged in. Powered by SMF 1. Either compression fittings or barbs 4 units. Quoted figures depend on your PSUs efficiency, the ambient temperature and the accuracy of the power meter. C1 mines are stand alone and do not require a proxy server or external controller.

- This shop is unavailable

Setup consists of installing the water pump, radiator, filling the coolant, connecting a PSU and an Ethernet cable. Skving antminer is used to design New-Style antminer cooling block. This allows for a large heat-transfer area, which keeps the PCBs exceptionally cool. Four hashing PCBs with 16 BM настройка per board are mounted to the both sides of two aluminum купить antminer s7 украина cooling blocks, which are mm-long, mm-high and 13mm-thick.

C1s require assembly but do not require an external controller. Strictly only 4 PCI-E antminer are required at stock speeds, however it will reduce cable temperatures by utilising all 8. Cut a paperclip into a U and insert it into the green wire and either black wire to the side of the green wire. Tape it up for safety. The power supply will now be controlled by its switch on the rear socket. Noise levels are reasonable considering the W of heat being removed with a single fan. If construction instructions were following correctly, the fan should be in a pull arrangement.

It is noteworthy that the end closest to the fan may become very hot to the touch extremely hot to the touch including the handles during operation, so please be careful during handling and maintenance. Step 1 Настройка are going to start by preparing the radiator. This is a high density, mm aluminium radiator with three mm fans installed already. Screw the two screws in to hold the 51mm in place, настройка careful not to damage the plastic threads.

Antminer C1 Standard | at-mr.ru

Step 2 Unscrew the two bottom corner screws on each end fan and discard the washers. Place the radiator stands between the fan grill and radiator on each side. Use the same screws as you removed to screw through the antminer grill, radiator stand and into the radiator. Locate the two short, silver screws and screw in the other side of the radiator stand into the radiator. Step 3 Next we will prepare the pump. Настройка is a 15W pump with 3m of head pressure and litres per hour of flowrate. Locate two fittings and screw them into the brass inserts. Step 4 Locate the tubing and cut three pieces from it, two of 70cm length and one of 40cm length.

You can do this with standard scissors but try and make the ends flat. Step 5 The C1 is next to be prepared. First open the case by unscrewing the 5 screws on each side. Locate the cable harness настройка plug in the 3 pin fan header to the header closest to the end with the antminer.

antminer c1 настройка

Unscrew the two настройка caps from the C1. A small amount of fluid may leak when you unscrew these caps. There are then various different ways to do the next stage depending on what type of fittings you have. Step 6a - Standard Fittings Screw in a fitting, slightly further than hand tight. Place a spring clamp on the 40cm length of tubing, and work it 10cm down the antminer so it is out of the way. Then push the tube over the end of the fitting until the tube hits the end of the fitting. This may be difficult or easy depending on the profile of that length of tubing. Slide the spring clamp over the fitting until it is squeezing the tubing over the smooth section of the fittings.

antminer c1 настройка

Repeat for the other side using one of the longer sections of tubing. Join the other half of the quick release connector to mate the pair.

Похожие статьи:

  • Antminer asic s7
  • Antminer s7 4730gh
  • Antminer 1490096
  • D3 antminer asic в наличии
  • Antminer s9 купить в курске
  • Buy antminer

  • Рекомендуем почитать:

  • asic antminer s7 купить москва
  • antminer u1 купить
  • видеокарта msi gtx 1060 6gt ocv1 купить
  • At-mr.ru - 2018 (c)