At-mr.ru

Antminer s5 1th

The S6, when it comes out with multiple blades and a rack mount chassis, should be a beast if they go that route like they have in the past with their S2 and S4.

ANTMINER S5+ is available to order, TH/S J/GH

The change in fans also resulted in a drop in temps by 4C. Being winter and the temps below freezing in the CCN mining laboratory, we pushed the clock speed freq up and were able to get the S5 to a stable 1. Overall another excellent chip and miner from Bitmain. The Antminer is also priced aggressively as well making it a good purchase. He noted they also have rolled out the S4 in HashNest as a choice that would allow customers gtx 1060 armor 6g ocv1 тесты run longer.

Now that the BTC value is rising many of the current miners will remain profitable longer as well. We also asked about extra-nonces support as many customers needed it to have the S5 run on multi pools like WestHash. At the time, 1th the S5 would be able to do them but they had not released the new firmware. Bitmain has now released the new firmware found hereand the miners are running great with this new ability. Hytekk has put up a guide on how to install the firmware and activate the extra nonce antminer. Thank you, Yoshi for the information and Hytekk antminer r1 the handy guide for those who had not updated the firmware before or enabled the extra nonce feature.

Номер товара на eBay:. Продавец берет на себя полную ответственность за это объявление о товаре.

antminer s5 1th

Характеристики товара Power Use W: Возобновить участие в аукционеесли страница не обновится. Введите число, равное размеру antminer ставки или превышающее. Это число указано под полем ввода ставки. Размер максимальной ставки не может быть снижен после того, как вы сделали эту ставку. If you buy the PSU with a little green connection board in our store, you need to connect it before you use. Here 1th the guide: Check out the PSU in the package. There is a connection board in the package. Connect the connection 1th to the PSU.

Then connect the 6pin cords. You only need 2 x 6pin to connect the miner. All stuff connected should be like this. Connect the antminer cord.

Antminer S5 | Antminer Distribution EU - Worldwide delivery

All connection was done. But actually, you need only 2 of them. We strongly suggest you connect the PSU via the two connectors far away from the little green board the controller. See the following picture you should use the connectors inside the red circle: The most 1th thing is: Open the IP scanning software, set the scan range as " Then you can find out the IP of the miner.

The following picture showing a scanning result of a antminer. The IP of this miner is " There is no this device at " You can also try every IP address if you are not very sure which IP is the miner. Sometimes, it is also shown as " Texas Instruments, Inc ", as the following picture showing: Whatever it showed as, you can just click the little triangle before the IP to see what the device is.

antminer s5 1th

For Antminer, it will show as " antminer Configuration " like the following picture showing. Power on the PSU. Scan the ip of the miner. Login the configuration page via the configuration ip you scanned eg.

Похожие статьи:

  • Extranonce antminer
  • Antminer s3 окупаемость в 2017 году
  • Что майнить antminer u3
  • Msi ati rx 580 armor 8g oc rtl
  • Antminer калькулятор

  • Рекомендуем почитать:

  • asic майнер antminer s7
  • At-mr.ru - 2018 (c)