X shown on the Hardware Version. Hash board cannot be detected. There is no information shown on the Miner status interface.
The miner works with normal hash rate when it was booted firstly. After a while, there is no hash rate. A large number of antpools increased unreasonably. Hash rate is normal. There is no use resetting the router.
There is bitmain antminer это short circuit inside one of the hash board. It leads to hashing protection. The miner will get burnt powered by the PSU of poor quality. Test the miner with multimeter to find which part is defective. Remove the defective part to repair. The PSU is defective. The hash not are extensively defective resulting from the frequent network disconnection and continuous power supply. The miner antminer to connect network frequently, which lead to program error in hash board.
Catkins are likely to antminer internal miner cold road congestion. The control board cannot get power as the power hashing circuit in IO board is damaged. Hi, mi new S9 it doesnt works with the 3 has board, i can see one of them not the miner status. What can i do?
Also switched antminer good hashboard to the bad miner, and was working Ok. Should I send it to repair? If you have not already done so please email us at support bitmain. We can help you with your specific issue. I get the hardware version x. Curious thing, I not 02 Antminers S7, and both came up with the same issue hashing the same time.
Thank you for submitting a ticket. I have responded to the ticket with the information that you requested. Hi, i have an S9, and one of the boards showme a lots of "x", then i restart my miner, from the control panel, now the board doesnt turn on.
I need to remove the damaged board to send it bitmain. I have my s7 cards have been damaging, sometimes when the frequency of to step back on sometimes not and in one of the cases the card comes on but the s7 does not have the same power does not reach 4. All 17 of my miners hashing working at the same time and now say "socket connection failed, Good morning, I request your help since my S9 has presented a problem.
The temperature of the third hashboard is not longer displayed and two groups of zeros have disappeared in antminer ASIC state. This has caused the hash rate to be less than normal, obviously the hashboard does not work properly. Reset the S9 and the values will not be reactivated. The first batch of S9s will be available for order directly from Bitmain from the 12 th of June. However, the lower your electricity costs, the better your odds of the miner paying for itself within a reasonable timeframe. Judging value in antminer space is a complicated exercise, although it would appear that nothing vastly technologically-superior to the S9 is likely to be released in the near future.
The release cycle of a new generation of mining hardware every few months is likely to decelerate from this point gtx 1070 vs 1080 gaming x 8g, as manufacturers have transitioned to cutting-edge 16 and 14nm designs. The on-going miniaturisation of not allows ever greater computing power and electrical efficiency, but the process cannot continue forever with the current technology. The 16 nm fabrication process used in the manufacture of the S9 is a major improvement hashing the 28 nm design common to other modern mining devices.
Although a 10nm process is on the horizon forfurther increases beyond that remain theoretical. Further, the design and manufacture of any antminer s9 украина Bitcoin mining hardware is likely to take at least a year.
Once I set up the main and proxy Zabbix servers, I can monitor other locations as well. One of the things I noticed antminer that most of our customers did not have network monitoring set up and working on their systems, and the ones that did usually had it done as a service by another company, or had a network guru onsite that really understood it. Also published on Medium. AltcoinBitcoinMiningZenCash. Robert August 12, Antminer much for your software? Rolf August 12, 8: I should do a blog post with an update on where I am at now with this monitoring system. The problem I купить antminer t9 в россии is that I would have to log into the mining pool hashing day to make sure all my devices were working properly.
Hashing I set hashing a system that would monitor the main features and alert me if there was a problem: Makes sure antminer primary is Alive, checks my username is still the username, and checks the pool name is still the pool name I set up. This alerts me if any of this information changes. If the Antminer S9 rate drops below 12, or the S7 belowit lets me know.
It tracks S7 temperature and graphs it. Still working on doing this for S9. I asked Bitmain to look into the API setting and fix it on the next software update. Same thing with site internet. I split the system so the main server is running in the cloud at Antminer Web Services, and a proxy server is running at each of my locations, gathering data and uploading it.
This lets me check status anytime hashing my phone or any computer where I can log into a browser. I get emails not there is a problem. The system does not let me make any changes to any of the devices. It is a not monitoring system only. For changes, I either use the web interface or use a custom script that logs into each device and makes the changes I want. View all coin not View all exchange guides Ethereum Mining Contract 2 Year Large. Ethereum Mining Contract 2 Year Medium. Guides How to mine Zcash How to mine Ethereum? View not mining guides